Gas detection equipment
JC-100 type fixed gas detection (alarm).
Published:2013-8-27   Views:5822
Product introduction:
JC100T intelligent modular gas detector for natural gas diffusion concentration detection, using imported electrochemical sensors, catalytic combustion type sensor, infrared sensor or PID detector, with excellent sensitivity and good repeatability; suitable for factories and application of LCD LCD or LED digital display shows the concentration value of gas leakage, exceeds the preset alarm immediately start sound and light alarm signal or driving the exhaust system; the international standard 4-20mA signal can be connected directly to the factory DCS system, RS485 digital signal connected with the factory PC; instrument using micro control technology, embedded system has the advantages of simple operation, complete function, high reliability, the performance of the leading domestic level.
JC100T intelligent modular gas detector has excellent performance, stable and reliable operation, convenient installation and maintenance, the measurement of gas range and other characteristics, great to meet the industrial site safety monitoring of equipment reliability and stable operation and measurement of gas species diversified requirements; has been widely used in petroleum, chemical, metallurgical, petrochemical, gas distribution, biochemical medicine and water treatment and other industries.
Function characteristics:
The instrument uses ultra low power 16 bit embedded advanced micro controller
The user can set the high and low alarm
◆ important operation need password authentication, effectively prevent the misoperation
The standard three wire 4-20mA current signal output, compatible with the existing alarm control unit or DCS (distributed control system)
◆ RS485 isolated digital signal is connected with the upper machine factory
◆ LED digital tube display or LCD display
◆ sensor fault automatic detection and display, and output the corresponding fault current signal
◆ -40 ~ +70 ℃ digital automatic tracking compensation, to ensure the accuracy of
The standard three button to achieve single point field maintenance
The two stage light alarm, relay output (external sound light alarm or drive exhaust and peripheral equipment)
The detector can be replaced with the type of sensor, the sensor can also be changed with different gas species, different range sensor module, detector, automatic recognition, without the need for calibration
Technical parameters:
◆ measurement range: see table
◆ working voltage: 24VDC ± 15%
The signal output: 4 ~ 20mA linear current output; or RS485 signal output
◆ response time: T90 less than 30 seconds
◆ recovery time: less than 30 seconds
The resolution: see table selection
◆ precision: ± 3%F.S
◆ display mode: LED digital tube display (optional liquid crystal display)
◆ environment temperature: -30 ~ +60 ℃ (specific basis of sensor parameters)
◆ the humidity of the environment: 10-95% R.H. (no treatment)
◆ explosion-proof grade: Exd IICT6 (flameproof applications); ExiaIICT4 (intrinsically safe application)
◆ protection grade: IP66
◆ installation thread: M20 x 1.5, G1/2
◆ use cable: 3 x 1.5mm2 or 4 × 2.5mm2 shielded cable transmission distance: ≤ 1000M
The size and weight: 160mm (L) 140mm (W) 85mm (H) about 1.5kg
Detection of gas meter
 

产品名称

被测气体

测量范围

可选量程

分辨率

响应时间

一氧化碳检测仪/报警器

CO

0-1000PPm

0-500/2000/5000PPm

1PPm

≤20

氧气检测仪/报警器

O2

0-25%VOL

30%VOL

0.1%vol

≤20

臭氧检测仪/报警器

O3

0-10PPm

0-100PPm

0.01PPm

≤20

硫化氢检测仪/报警器

H2S

0-100PPm

0-502001000PPm

1PPm

≤30

氢气检测仪/报警器

H2

0-1000PPm

0-5000PPm

1PPm

≤30

氯气检测仪/报警器

CL2

0-20PPm

0-10100PPm

0.1PPm

≤30

氨气检测仪/报警器

NH3

0-100PPm

0-505001000PPm

1PPm

≤30

二氧化硫检测仪/报警器

SO2

0-20PPm

0-501000PPm

0.1PPm

≤30

一氧化氮检测仪/报警器

NO

0-250PPm

0-500PPm

0.1PPm

≤30

二氧化氮检测仪/报警器

NO2

0-20PPm

0-50100PPm

0.1PPm

≤30

甲醛检测仪/报警器

CH2O

0-50PPm

0-510PPm

0.01PPm

≤30

氯化氢检测仪/报警器

HCL

0-20PPm

0-20100PPm

0.5PPm

≤30

可燃气体检测仪/报警器

EX

0-100%LEL

0-100%LEL

1%

≤30


Previous:No
Next: JC-100 type gas alarm controller
Copyright